Injection moulding optimisation thanks to adapted mould movement

Cycle times of 3 to 4 seconds are commonplace in the injection moulding production of packaging parts. The pressure to reduce production times continues to increase. ENGEL has developed an intelligent assistance system that automatically optimises the acceleration phases of movement sequences in injection moulding. The result is faster movements.

The ENGEL viper linear robots made the start. What is new is that iQ motion control is also available for mould movement in the injection moulding machine. The packaging industry in particular benefits from this.
 

Opening and closing the injection mould accounts for a large part of the production time in high-speed applications. This becomes clear in the production of thin-walled containers. They are produced in a 4-cavity mould on an ENGEL e-speed 280 injection moulding machine.

The facts:

• Total cycle time: 3.15 seconds
• Injection time: 0.08 seconds
• Cooling time: 0.8 seconds

The demoulding of the parts takes 2.27 seconds. Of this, only 1.0 seconds can be attributed to the removal by the robot. The mould movement therefore takes the remaining 1.27 seconds, which corresponds to 40% of the production time.

Closing the mould after removing the thin-walled containers takes 0.77 seconds, including the build-up of clamping force. To shorten the injection moulding cycle, the injection process already starts at 70% of the set clamping force. An even earlier start is not possible, as the material could otherwise flow into the parting line of the mould. But with an injection time of only 0.08 seconds, the potential is manageable anyway. No further time can be saved by parallel movements. To reduce the cycle time in injection moulding, the only option is to optimise the mould movement.

0.77 seconds for the closing movement are is already sporty for a stroke of 285 mm and including the closing force build-up. The drive constantly alternates between acceleration and deceleration. The movement time can be optimised if you know when to accelerate or decelerate and how much.
This is precisely where iQ motion control comes in. The assistance system evaluates the relevant parameters such as clamping force, stroke and mould weight for the respective application. It also calculates the optimal accelerations. The drive power is used optimally, which shortens the mould movement by an average of 10%.
 

The use of iQ motion control results in the following advantages and optimisations in injection moulding:

• iQ motion control takes over the fine-tuning of the mould movement - for each individual application.
• The user benefits from shorter dry cycle times of the injection moulding machine.
• The operation of the machine is simplified by the independent optimisation.

In the production of the thin-walled containers, the cycle time was reduced from 3.15 to 3.0 seconds. In relation to the dry cycle time of the injection moulding machine, this results in a reduction of 12%-1.12 instead of 1.27 seconds.

The graphic shows, based on the motor movement and the drive torque, at which points in the injection moulding cycle time is saved. By defining maximum values, iQ motion control ensures that there is no increased load on the mechanics and drive technology.

The comparison with the reference curve without iQ motion control makes it clear that the greatest potential for injection moulding optimisation lies in the first 0.3 to 0.5 seconds of the closing movement. The greater drive torque leads to higher speeds at an earlier stage, which saves time. In addition, the torque is built up and released much more evenly. This also saves time.

With iQ motion control, ENGEL has developed an assistance system that optimises the mould movement of high-performance machines. This makes the full potential of mechanics and drive technology available for every application.

The practical test clearly showed what iQ motion control can contribute to injection moulding optimisation:

• Dry cycle time of the injection moulding machine reduced by an average of 10%.
• Production output increased by up to 5%.
• Automatic injection moulding optimisation, without additional effort for the machine operator.

For more ways to optimise your injection moulding production, read the blog article Tips for process optimisation in injection moulding.