ENGEL Global

Injection moulding optimisation thanks to adapted mould movement

iQ motion control reduces the cycle time in the high-performance range

An injection moulding cycle that is one tenth of a second shorter already optimises output in injection moulding by 3%. ENGEL's iQ motion control software makes exactly that possible and ensures greater productivity.

Picture shows mould movement of an ENGEL injection moulding machine

Why produce faster and faster?

Cycle times of 3 to 4 seconds are commonplace in the injection moulding production of packaging parts. The pressure to reduce production times continues to increase. ENGEL has developed an intelligent assistance system that automatically optimises the acceleration phases of movement sequences in injection moulding. The result is faster movements.

The ENGEL viper linear robots made the start. What is new is that iQ motion control is also available for mould movement in the injection moulding machine. The packaging industry in particular benefits from this.
 

Cycle optimisation in high-performance injection moulding

The initial situation

Opening and closing the injection mould accounts for a large part of the production time in high-speed applications. This becomes clear in the production of thin-walled containers. They are produced in a 4-cavity mould on an ENGEL e-speed 280 injection moulding machine.

The facts:

  • Total cycle time: 3.15 seconds
  • Injection time: 0.08 seconds
  • Cooling time: 0.8 seconds

The demoulding of the parts takes 2.27 seconds. Of this, only 1.0 seconds can be attributed to the removal by the robot. The mould movement therefore takes the remaining 1.27 seconds, which corresponds to 40% of the production time.

 

The challenge

Closing the mould after removing the thin-walled containers takes 0.77 seconds, including the build-up of clamping force. To shorten the injection moulding cycle, the injection process already starts at 70% of the set clamping force. An even earlier start is not possible, as the material could otherwise flow into the parting line of the mould. But with an injection time of only 0.08 seconds, the potential is manageable anyway. No further time can be saved by parallel movements. To reduce the cycle time in injection moulding, the only option is to optimise the mould movement.

The solution

0.77 seconds for the closing movement are is already sporty for a stroke of 285 mm and including the closing force build-up. The drive constantly alternates between acceleration and deceleration. The movement time can be optimised if you know when to accelerate or decelerate and how much.
This is precisely where iQ motion control comes in. The assistance system evaluates the relevant parameters such as clamping force, stroke and mould weight for the respective application. It also calculates the optimal accelerations. The drive power is used optimally, which shortens the mould movement by an average of 10%.
 

Such short movement times can only be realised through a mechatronic approach. Motion planning, drive control and mechanics must be perfectly coordinated so that the existing components can develop their full performance. ENGEL has recognised this potential and included iQ motion control in the standard scope of the high-performance e-speed and e-cap series.

Image shows control enginerr at ENGEL
Christoph Stöger, Development Control Technology ENGEL Austria

Advantages of iQ motion control in high-performance injection moulding

The use of iQ motion control results in the following advantages and optimisations in injection moulding:

  • iQ motion control takes over the fine-tuning of the mould movement - for each individual application.
  • The user benefits from shorter dry cycle times of the injection moulding machine.
  • The operation of the machine is simplified by the independent optimisation.

 

iQ motion control reduces the dry cycle time of the injection moulding machine by around 10%

In the production of the thin-walled containers, the cycle time was reduced from 3.15 to 3.0 seconds. In relation to the dry cycle time of the injection moulding machine, this results in a reduction of 12%-1.12 instead of 1.27 seconds.

The graphic shows, based on the motor movement and the drive torque, at which points in the injection moulding cycle time is saved. By defining maximum values, iQ motion control ensures that there is no increased load on the mechanics and drive technology.

The comparison with the reference curve without iQ motion control makes it clear that the greatest potential for injection moulding optimisation lies in the first 0.3 to 0.5 seconds of the closing movement. The greater drive torque leads to higher speeds at an earlier stage, which saves time. In addition, the torque is built up and released much more evenly. This also saves time.

Conclusion: Is iQ motion control a useful addition to injection moulding optimisation in the high-performance sector?

With iQ motion control, ENGEL has developed an assistance system that optimises the mould movement of high-performance machines. This makes the full potential of mechanics and drive technology available for every application.

The practical test clearly showed what iQ motion control can contribute to injection moulding optimisation:

  • Dry cycle time of the injection moulding machine reduced by an average of 10%.
  • Production output increased by up to 5%.
  • Automatic injection moulding optimisation, without additional effort for the machine operator.

For more ways to optimise your injection moulding production, read the blog article Tips for process optimisation in injection moulding.

Would you like to optimise your injection moulding production and produce faster?

More about our products from the article

iQ motion control for machines

Up to 12% shorter dry cycle time of the injection moulding machine in high-performance injection moulding

reading time approx. 8 minutes
Contact us
We'd like to hear from you.
ENGEL Team
Austria

Get in touch

Personal Information
How can we help you?
Submit
Please note the information on data protection at ENGEL at www.engelglobal.com/dataprotection.

Get in touch

We'd like to hear from you.
ENGEL Team
Austria
Personal Information
How can we help you?
Submit
Please note the information on data protection at ENGEL at www.engelglobal.com/dataprotection.
Available languages
Europe
North & Central America
Asia